-
Who This Checklist Is For (and What It Won't Fix)
-
The 7-Step Check (Run This Before Every Order)
-
Step 1: Translate the part number into a sentence
-
Step 2: Match the end connection to the pipe — both ends
-
Step 3: Pull the catalog row behind the eight-digit number
-
Step 4: Check the unit of measure, not just the quantity
-
Step 5: Confirm the seal on the swivel side is included
-
Step 6: Print the PO and check it with a pen
-
Step 7: Inspect on arrival, not when you need it
-
Step 1: Translate the part number into a sentence
-
Errors This Checklist Won't Catch
-
Who This Checklist Is Not For
Who This Checklist Is For (and What It Won't Fix)
I've been handling valves and pipe fittings orders for eleven years. I've personally made 23 mistakes that were expensive enough to remember, totaling somewhere around $14,000 — maybe $15,000 if I go back and add in the freight. Now I maintain the checklist our team uses before anything gets submitted.
Here's the whole thing. Seven steps, about twenty minutes if nobody interrupts you. It's written for people who are new to pipe fitting and have just been handed ordering responsibilities — the ones who haven't been schooled by a swivel elbow yet.
Which, honestly, is half of what "how to get into pipe fitting" actually means. The other half is knowing what you're buying.
The 7-Step Check (Run This Before Every Order)
Step 1: Translate the part number into a sentence
Apollo Valves' numbering gives you a lot if you actually read it. APXFAE1212 breaks down as APX for the product series, FAE for female swivel elbow, and the tail end as the size designation. An eight-digit number like 10075810 is a catalog number — you can't decode it, you have to look it up.
My rule: I have to be able to say the part out loud in plain English before I submit. "Half-inch PEX, swivel nut on one end, elbow." If I can't say it, I don't send the order.
In 2016 I got this wrong. I read FAE as female adapter elbow and figured "swivel" was just a naming quirk. It isn't. A swivel elbow has a rotating nut; an adapter elbow has a threaded port. Our customer needed to seat a fitting on a rigid connection with a fixed orientation. 320 pieces, roughly $1,900 with freight, straight onto the returns shelf. That was my first real tuition payment.
Check point: you can explain the part number out loud without looking at the screen.
Step 2: Match the end connection to the pipe — both ends
Connection types are where a fair amount of trouble starts. PEX crimp, PEX expansion, NPT threads, copper solder, CPVC solvent weld — each has its own sizing logic. NPT is tapered thread, made to ASME B1.20.1, so "half inch" on your PO is only half the story.
Here's the one most people skip: if the part is a transition fitting (PEX × NPT, for example), spell out both ends separately on the paperwork. Don't let them share one sentence. I've watched people sign off after verifying the PEX end and then get blindsided by the other side.
I'm not a licensed plumber, so I can't speak to torque values or tape technique. What I can tell you is to write both dimensions on the order so there's a paper trail.
Step 3: Pull the catalog row behind the eight-digit number
A number like 10075810 means nothing until you're looking at the matching row in the catalog. That row gives you size, body material, pressure and temperature limits, and which certifications apply. That's what you check — not the photo on the product page.
Certifications worth confirming in writing:
- NSF/ANSI 61 for drinking water system components
- NSF/ANSI 372 for lead content (0.25% weighted average)
- ASSE 1015 for backflow prevention devices
If the catalog row or the spec sheet doesn't list them, call the distributor and ask. Not "I think it's fine." Asking takes four minutes. A wrong answer takes weeks.
Step 4: Check the unit of measure, not just the quantity
Is that PEX fitting sold each, or by the bag, or by the box? The numbers look identical and the outcome is 25 times different.
We got hit by this in 2019. I put in an order for 40 units, meaning 40 singles. It was 40 boxes of 25. At $1.20 each, I signed off on $1,200, not $48. The surplus sat on our shelf for over two years because our customer was never going to use that volume. Direct damage was somewhere around $1,150, plus shelf space I'd rather not think about.
I second-guessed myself right after submitting — I remember thinking I should call the vendor and confirm the pack size. I didn't. The order confirmation came back and the number was right there in black and white.
Looking back, I should have picked up the phone. At the time, though, I told myself "nobody gets a small order like this wrong."
Step 5: Confirm the seal on the swivel side is included
This is the second layer of the Step 1 mistake, and a much easier one to miss. Swivel nut fittings seal on a gasket or O-ring, and that seal often does not travel with the fitting. It can be a separate line item. It can be sold in packs.
Check point: the phrase "is the gasket included" goes in the notes field of the PO, every time.
I still forget this one (note to self: get it into our ERP's default notes field). Last time I missed it, the vendor sold the seals in packs of 10 and we had 60 installs queued for that afternoon. I spent an hour digging through bins, which was not my finest afternoon.
Step 6: Print the PO and check it with a pen
This sounds dumb. It's the highest-leverage step on the list. I print the purchase order and work down it with a red pen against the catalog page, which I have open on the screen. Not scrolling through line items on the screen — on paper.
Why paper works: on screen I can flick through and everything looks fine. Paper makes me slow down.
I made this mandatory for our team after the third rejection in Q1 2024. In the 18 months since, the process has caught 47 potential errors. That's roughly two and a half a month, and probably half of those would have gone all the way to a return.
Step 7: Inspect on arrival, not when you need it
Open one box. Pull three or four random pieces. Match the cast or laser-marked number to the PO.
Timing matters here. Special-order return windows tend to be shorter than stock-item windows — sometimes measured in weeks rather than months. A box that sits in the rack for a quarter can lose the return option it had on day one. That one cost me a fight with a supplier back in 2021.
Errors This Checklist Won't Catch
The checklist covers the ordering process. Below are the problems it can't do anything about.
People think cheap valves are the ones that fail. More often, the same valve gets installed near the top of its pressure limit or against the wrong media — the problem is selection, not manufacturing. The identical part that lasts a decade in the right application can be done in one quarter in the wrong one.
Here's something vendors won't spell out for you: a quoted "standard lead time" usually contains buffer a supplier uses to sequence their own production queue. It's not your order's timeline. If you've got a hard install date, ask for the projected ship date instead. Asking for "standard lead time" gets you a number that means something different than you think.
And emergency orders. This checklist takes twenty minutes. If the truck loads this afternoon, it won't help you. That's the case where you call the distributor and ask who has stock on the shelf. Don't guess.
Who This Checklist Is Not For
If your orders already pass through an engineering reviewer who checks drawings and spec sheets line by line, skip this. It's redundant for you.
One more thing, and I'll be blunt about it: the "who makes air compressors" or the "460 rancher gas chainsaw" searches that show up alongside valve queries — those aren't my territory. I don't touch gas-powered equipment and I can't help you source it. What I can help with is not buying the wrong part number.
And the honest boundary: if your order is 500 pieces or more, involves custom configuration, or touches certification compliance, you don't want a seven-step checklist and a buyer. You want an engineering review. That's not pessimism — it's putting the job where it belongs.